Powers 470 Series VisuGuard Pressure-Balancing Tempering Manuel d'utilisateur télécharger pdf

Note: Installation should be in accordance with accepted

plumbing practices. Finish all piping thoroughly before

installation.

VALVE PIPING

1. Facing the front of the mixer, connect hot water supply to

the left side and cold water to the right side of the valve.

These supply inlets must be piped correctly or the valve

will not mix properly (inlets are labeled on the bonnet). If

supply lines are reversed, see “mixing plate rotation.”

2. All VisuGuard LCD mixers are supplied for 4-port applica-

tions and can be modified for 3-port applications by

using the included

⁄8″ sweat plug. Refer to “Dimensional

Data” to determine proper installation.

3. Do not remove the rough-in guide; you will use it to posi-

tion mixer to the proper depth within the wall later.

4. If copper tubing is used, use flared fittings to connect tub-

ing to mixer. The heat generated during the solder opera-

tion could damage the internal parts of the mixer. Inlet

checkstops for direct sweat connections are available.

If flared fittings or checkstops cannot be used,

remove the balance chamber before soldering (see

balance chamber removal).

TRIM PLATE / HANDLE ASSEMBLY

Refer to exploded view to identify parts.

1. Using the rough-in guide to aid in cutting the proper

access hole into the finished wall.

2. Apply the adhesive trim plate gasket to the inside edge

of the trim plate. Proper application results in approxi-

mately

⁄4″ gasket compression against finished wall.

3. Remove rough-in guide.

4. Locate and insert the thermistor (temperature probe)

into the supplied compression fitting at the mixer outlet.

See proper probe depth below (Figure 1). Improper

installation of depth probe can result in imprecise tem-

perature readings. Firmly tighten to prevent leakage.

5. Apply trim plate to wall (valve handle inserted through

trim). Do not hang trim plate on wall using temperature

probe wire as this could cause damage to probe.

6. At this point it is wise to pressurize and test the system

to verify zero leakage and set maximum temperature

settings prior to finishing the trim application.

7. Maximum temperature setting adjustment: To change

setting, remove splined stop by slipping O-ring up on

stem. Rotate temperature adjustment stem to desired

maximum temperature. Position splined stop on the

adjustment stem so that it contacts the bonnet stop.

Replace O-ring.

5/16’’ 1/16’’

Temperature

probe

Figure 1: Probe Figure

2.60 Ref.

Handle

set screw

Stem

Figure 2

Puller

Puller Clasp

Figure 3

(continued on other side)

INSTALLATION INSTRUCTIONS

PRESSURE-BALANCING TEMPERING VALVE

WITH LCD TEMPERATURE DISPLAY

Model F473 shown ADA-compliant handle operation

Form II473

1 2

Résumé du contenu

Page 1 - INSTALLATION INSTRUCTIONS

Note: Installation should be in accordance with acceptedplumbing practices. Finish all piping thoroughly beforeinstallation.VALVE PIPING1. Facing the

Page 2 - Figure 4: Exploded View

II473 Page 2© November 2001 PowersUSA Phone: 800.669.5430 • Fax: 847.229.0526Canadian office: Phone: 888.208.8927 • Fax: 888.882.1979www.powerscontrol

Plus de documents pour Accessoires pour l'eau Powers 470 Series VisuGuard Pressure-Balancing Tempering

Voir le document Powers 470 Series VisuGuard Pressure-Balancing Tempering Manuel d'utilisateur

Powers 470 Series VisuGuard Pressure-Balancing Tempering Manuel d'utilisateur (8 pages)

Commentaires sur ces manuels

Pas de commentaire

Powers 470 Series VisuGuard Pressure-Balancing Tempering Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires pour l'eau Powers 470 Series VisuGuard Pressure-Balancing Tempering . Powers 470 Series VisuGuard Pressure-Balancing Tempering Valve with LCD Temperature Display User Manual Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Accessoires pour l'eau Powers 470 Series VisuGuard Pressure-Balancing Tempering

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires pour l'eau Powers 470 Series VisuGuard Pressure-Balancing Tempering